MTI Forum

Some projects will use temporal coating for stainless steel 304 or 316 equipment ...

Hi everyone I am looking for an effective method to clean a 4-inch Stainless ...

Matt. Are you certain that this is not migrated gases (e.g. H2) fromt he ...

We have found lined pipes with only liner left due to CUI. I believe they were ...

From AmeriTAC 148 Forum Discussion Marc Cook (Tricor) commented ...

From AmeriTAC 148 Forum Discussion Will H oskins (Eastman Chemical) ...

Kyle – I suspect you have already had input and have moved on from this topic. ...

Hardin Wells reacted to your message:

Dear Curtis, If nitriding scales on austenitic steels spall-off, then most ...

I know this message is coming quite late, but I still wanted to share some information ...

William, my pal Aaron is right on. We had the exact same issue with Safety ...

Xiaowei, my experience with titanium limited, & Outokumpu has elected not to ...

Hello Deborah, Laser beam is an acceptable welding process for deposition ...

Karl, I didn't know that any producer is currently making Ti Grades ...

Thank you for all the quick and insightful reactions. This warrants further ...

I asked this very question back in the Fall 2018 Information Exchange at the ...

Peter, I would be cautious about using this titanium equipment with these ...

Hi John, Midad Factory in Dammam, Saudi Arabia is Saudi Aramco and Sabic approved ...

Hardin Wells reacted to your message:

Bill both PTFE and PFA will handle the temperatures and the full range of Sulfuric ...

Pham, Loan reacted to your message:

We use Moffatt & Nichol for our underwater wharf work. They have a pretty large ...

My apologies. I think this is the link for the Cincinnati company.

Hi Mohammad: I would echo the comments of Bill Salot, down-thread. The ...

Is there a handy-dandy, published diagram that addresses corrosion of carbon ...

I can confirm Dale's and Berhard's answers with our internal ARKEMA feedback. ...

Jeremy, Proper Engineering of the Supports and Foundation are ...

Thank you all for your responses. This has been very helpful! ------------------------------ ...

Hi, Does someone have experience with this and is able to share their experience ...

Hi Jennifer, Ive sent you an email. Done some overlay weld repairs for copper ...

Jazmin, Similar to what Xiaowei has suggested, pH measurement of the solution ...

Does anyone have experience with upgrading hydrocarbon sparger(s) material to ...

Khaled Zanoon reacted to your message:

Pedro, I am not exactly sure what you are looking for a specific PTFE(M) grade, ...

Thank you everyone for the rapid response. Appreciate the comments and experiences ...

From AmeriTAC 147 Forum Discussion Marc Cook ( Tricor): Fr acture ...

From AmeriTAC 147 Forum Discussion Jeremy Nelson (Koch Ind) : L ...

Dear Maria, Antistatic PTFE typically contains less than 2% graphite. Every ...

To add to Dale's comment regarding weather related issues, I've had issues with ...

Rob, HTHA has been reported very low carbon content 100% ferrite alloys where ...

Thanks. This is what I was looking for. ------------------------------ Bob ...

SImilar data to those already offered by others. I recall a similar application ...

From AmeriTAC 147 Forum Discussion Maurice Wadley, DuPont: When he's not ...

From AmeriTAC 147 Forum Discussion Bob Hurst, Becht: I don't know how much ...

Hi For protection of CR- Ni material from metal dusting, a low level (at ...

Hi, The service water (potable water equivalent quality) that flows through ...

Andrew, I think this forum topic is a great opportunity to point out that the ...

Does anyone know of a good stainless steel tank manufacturer/fabricator in the ...

We are replacing ammonia valves in an ammonium diuranate system. These valves ...

To answer the questions: It was polished and as far as we can tell, there ...

Hi Curtis, I know I am late, but hopefully this will be additive the next ...

From AmeriTAC 146 Forum Discussion Dan Janikowski (Webco) – pH must be watched, ...

From AmeriTAC 146 Forum Discussion Aaron Rose (BASF) – Last time he did that ...

From AmeriTAC 146 Forum Discussion Looking for Flow rate limits ...

From AmeriTAC 146 Forum Discussion M urray Pearson (Hatch) : areas ...

Hi Steven: The attached paper is useful, and I think provides what you ...

I used ASK MTI AI for the first time today. I'm very impressed. It's making ...

William, We have experience with impedance heated piping systems. Generally, ...

I am involved in the assessment of a 45 year old carbon steel (A36) tank ...

https://globalsilicones.org/wp-content/uploads/2020/10/Chlorosilanes-Manual.pdf ...

Does anyone have information on what are the highest strength cast Al alloys ...

Right. As has been noted in API P 582 4th ed. Para D.9.2 d). Some other Ni-base ...

Andrew, It looks like there is plenty of data for PEEK and anhydrous ammonia ...

Hello almighty think tank, I performed a search using the MTI AI tool but ...

F02 was reported flame under insulation on inlet header pressure gauge tapping ...

In addition to the problems associated with loading the ASSET program to a computer, ...

Thanks William! You inspired me to search more technical papers on this topic, ...

The history is "Saramet" alloys is: in the 1980s Chemetics got a "use patent" ...

Bob, this is in response to your question about electrical isolation of flanges ...

Hi William, attached a few pictures from hydrogen grooving on the side wall ...

I am looking for bearing form a high pressure oxidation leach pilot plant. ...

This failure sounds similar to a case I observed many years ago.(1985) Air Products ...

Thanks, Ed for your feedback . Regards, Rajaram Chidambaram Materials ...

Not sure why my previous post was cut off, but I was trying to say that non-metallic ...

Hi Steve, We do use the A923-C test for the S32750 tubing ...